Good budget free project 2-storey cottage, download it for free, and you will see that you have a great built spacious house!
Architectural and planning solution developed in accordance with SNiP 2.08.01-89 "Residential buildings".
The layout of the house is solved in two levels. For conditional level 0,000 accepted the mark the first floor. At elevations below 0,000 are: porch, as well — ground floor ceiling height of less than 1.2 m At around 0,000 comprises of an entrance hall, living room, kitchen, guest bedroom-study, bathroom with shower cabin, boiler station.
On the second level (at around 3,200) there are two bedrooms and a large lounge. Next to the exit from the main staircase (above the bedroom doors) can be equipped with a insulated hatch for access to the attic space.
In the non-residential attic there are no isolated rooms, it is intended for technical purposes.
Exterior finish of the cottage
The outer walls with a total thickness of 400 mm are made of 150×150 timber, followed by external insulation with mineral wool plates of 100 mm and facing in" half-brick " 120 mm with an air gap of 30 mm.
The brick facing can be covered with a plaster layer and painted or, for example, tiled "under a wild stone".
The color scheme of the walls is beige or gray-brown.
The base outside is lined with concrete blocks 400x200x200 with "torn" front surface, which in addition to decorative and perform a structural function. The color of the blocks is dark gray with a greenish or dark blue tint. Can be used conventional blocks (or casting concrete), followed by finishing the surface of the cap under the "wild stone".
Wooden elements are either tinted or simply painted (preferably in dark brown or red-brown).
The main roof and facade roofing eaves are made of bitumen ("soft") tiles of dark brown color. Caps over a pipe and ebb under Windows — from flat metal sheets of the same color, as a roof. The Windows are made of plastic (or wood) of dark brown color.
The supporting structures of the building are the walls of timber 150×150 and floors: base-from a combined monolithic concrete with steel longitudinal beams; first floor-on wooden beams 100×200.
The spatial rigidity of the building is provided by the joint work of longitudinal and transverse walls with a floor disk. The walls of the strip Foundation and the ground floor are made of monolithic reinforced concrete and concrete blocks 400x200x200 (on the outer side of the base — blocks with a decorative outer surface or plastered and finished under the "wild stone").
Horizontal waterproofing between the base and cap, base and walls of the 1st floor slab consists of 2 layers of roofing material or the 1st of the gidrostekloizol. Vertical waterproofing-covering with cold and hot bitumen for 2 times. The outer walls with a total thickness of 400 mm are made of 150×150 timber, followed by external insulation with mineral wool plates of 100 mm and facing in" half-brick " 120 mm with an air gap of 30 mm.
The inner wall is made of 150×150 timber with double-sided covering (total 200 mm). Partition walls are made of timber 100 mm, followed by paneling or plaster. Floors: basement-from the combined monolithic concrete with steel longitudinal beams; first floor-on wooden beams 100×200.
Roof-attic truss construction. Rafters-wooden. Elements of bearing structures made of softwood with a moisture content of not more than 20%. The roof is ventilated, insulated, wooden truss structures.
Wooden structures in contact with the masonry, protect against rotting gasket — two layers of roofing and carefully antiseptirovat.
Wooden structures treated with antiseptics and flame retardants.
Insulation — plate of polystyrene foam or hard mineral wool.
Technical and economic characteristics of the project:
- Total area: 96.6 m2
- Living area: 73 m2
- Building area: 76 m2
- Construction volume: 530 m2
This wonderful free project 2-storey cottage is quite suitable for a country house and for urban construction.